Nintendo Network Router 2000 Manuale Utente

Orion 2000 Cable Router User’s Guide Rev. 1.2c Firmware 2.59.2013 Oct 20th, 2003

User’ Guide 10 USB cable to the PC by following next section instructions. Installing the Hardware This section e

User’ Guide 11 2. Insert the CD into the PC’s CD-ROM and click Next. You will see the following screen. 3. Sel

User’ Guide 12 4. Check the CD-ROM drive check box and verify that the CD is in the CD-ROM drive. Click Next to

User’ Guide 13 CAUTION: You must verify that Ambit USB Cable Modem appears on the screen. If USB Composite Device

User’ Guide 14 7. If the above screen appears, you must insert the Windows 98 CD so that Windows can copy the rema

User’ Guide 15 10. Choose Yes to restart your computer. 11. After the computer is rebooted, verify that the USB

User’ Guide 16 Installing the Software Drivers in Windows Me Operating System To install the cable modem software

User’ Guide 17 4. Click Next. The computer automatically installs the necessary driver files. 5. Click Finish

User’ Guide 18 6. Click Yes to restart the computer

User’ Guide 19 Installing the Software Drivers in Windows 2000 Operating System To install the cable modem softwar

User’ Guide 2 Contents 1. BEFORE YOU BEGIN ...

User’ Guide 20 3. Select Search for a suitable driver for my device (recommended. Then select Next. You will see

User’ Guide 21 Next to have Windows locate the necessary driver files. You will see the following screen. 5. Cli

User’ Guide 22 7. Click Finish to complete the installation. 8. After the installation is completed, verify that

User’ Guide 23 Installing the Software Drivers in Windows XP Operating System 1. Power on your PC. After your co

User’ Guide 24 3. Click Finish to complete the installation.

User’ Guide 25 Troubleshooting the USB Installation None of the LEDs is on when I power on the LAN Cable Modem.

User’ Guide 26 4. Select USB Composite Device and click Remove 5. Click Refresh The Add New Hardware Wizard window

User’ Guide 27 necessary files from you computer. 3. Installing the Modem Using the Ethernet Port This chapter exp

User’ Guide 28 4. Plug the cable modem’s power adapter into the cable modem’s power jack and into a wall outlet or

User’ Guide 29 communications with your cable service provider. • If your PC is connected to a hub or gateway, try

User’ Guide 3 Image ...

User’ Guide 30 4. Cable Modem LEDs and Connectors This chapter describes the functions of the cable modem’s LEDs a

User’ Guide 31 areas. Connectors on the Back of the Modem This list of connectors describes where to connect th

User’ Guide 32 5. Telnet commands The Cable Router telnet Login and Password: Login: Password: ** Note:

User’ Guide 33 line Configure a terminal line write Write configuratoin to nvram re

User’ Guide 34 Debug ¾ debug Display corresponding message, the protocol debug just show packet information send t

User’ Guide 35 all Disable all debugging functions Image ¾ image upgrade {1|2} Download the sp

User’ Guide 36 Ping statistics: Packets sent: 6; received: 6; Lost: 0 (0% loss) Round trip time in milli-seconds

User’ Guide 37 Show ¾ show dhcp Display all options provided in DHCP response. Example: CM>show dhcp TFTP Ser

User’ Guide 38 2 172.17.0.0 255.255.0.0 172.17.100.134 1 connected 3

User’ Guide 39 Downstream SNR : 33.28 dB Upstream information Upstream Channel ID : 2 U

User’ Guide 4 Reset...

User’ Guide 40 Interface Cable MAC address: 0002.8A32.4101 IP address 10.54.5.186 subnet-mask 255.25

User’ Guide 41 RIP update time: 15 seconds RIP response time: 30 secconds RIP expire time: 1

User’ Guide 42 Example: CM>show cpe-limit MAC address limit: unlimited IP address limit: unlimited ¾ show

User’ Guide 43 ¾ show rip Display RIP information Example: CM>show rip IP Route disables. Key Chain-1 info

User’ Guide 44 Example: CM>show nat timer Aging Timer (second) ICMP protocol : 5 (secs) UDP protocol : 1800

User’ Guide 45 CM>show pppoe-forwarding PPPoE-forwarding disable. NVRAM ¾ nvram factory-default Restore cable

User’ Guide 46 ¾ host-name delete Delete host-name. Example: Customer-123> host-name delete Delete host name w

User’ Guide 47 ¾ dhcp gateway {ip address} Set local DHCP gateway ip address. ¾ dhcp reserve-mac add {ip address}

User’ Guide 48 ¾ dhcp dns delete {1~4/all} Remove one/all dhcp server dns ip address(es) setting. ¾ dhcp domain-

User’ Guide 49 NAT : Enable WAN SETUP : NAT public IP configuration : Automatically NAT public IP address : 68.101.1

User’ Guide 5 1. Before You Begin Your new cable modem provides high-speed access to the Internet by an active Inte

User’ Guide 50 1 192.168.100.1 192.168.100.21 DNS server(1) 68.6.16.30 DHCP server lease time : 1800

User’ Guide 51 Set static router address Example: CM>nat static gateway 68.5.202.1 Set NAT public Gateway IP to

User’ Guide 52 ¾ interface ethernet mac-address {mac address} Assign MAC address to ethernet interface. Example: C

User’ Guide 53 ¾ interface cable rip send-version {1|2} Set RIP version 1 or version 2 on cable interface. ¾ int

User’ Guide 54 IP ¾ ip route {enable/disable} Enable/disable routing with RIP. Default routing mode is RIPv2

User’ Guide 55 Enable/disable silence mode. If set, the cable router just listen RIP message, it doesn’t send any RI

User’ Guide 56 Enable|disable the CM web access via CPE interface. ¾ web-access cable {enable|disable} Enable|disa

User’ Guide 57 CM>access-list 21 permit 192.168.100.10 0.0.0.0 Note: No network packet will be filtered 3) Set

User’ Guide 58 Limit the number of CPEs based on MACs, or unlimited SNMP ¾ snmp community Show current S

User’ Guide 59 6. Mode of Operation Bridge mode Bridge mode is the factory default setting. NAT mode ¾ ip nat ena

User’ Guide 6 Prepare Your Area for Cable Modem Installation Before installing your cable modem, you should first p

User’ Guide 60 Routing mode ¾ ip route enable Default setting for routing mode is RIPv2 with DHCP disabled automat

User’ Guide 61 NAT/Routing mode ¾ ip natroute enable Enable NAT and Routing simultaneously. Enable natroute will al

User’ Guide 62 7. Web User Interface Accessing the Web User Interface 1. The PC connected to the cable modem must

User’ Guide 63 Cable Modem Information

User’ Guide 64 Cable Modem Status

User’ Guide 65 Downstream

User’ Guide 66 Upstream

User’ Guide 67 Upstream Burst

User’ Guide 68 Operation Parameters

User’ Guide 69 Event Log

User’ Guide 7 Be sure to follow the instructions provided for the port that you want to use. Using the USB port al

User’ Guide 70 Router/NAT configuration Bridge Mode In Bridge mode, no configuration is required. The Orion 2000 Ca

User’ Guide 71 NAT Mode Gateway LAN Interface • IP Address Gateway private NAT IP address • Subnet Gatewa

User’ Guide 72 Router Mode

User’ Guide 73 Routing Protocol LAN Interface • Public IP Address Gateway(same as the Cable Modem’s ethernet inter

User’ Guide 74 • Authentication Key Chain Key Chain 1 • Listing of key • Input key Index ID, Key String, Start

User’ Guide 75 NAT Router Mode

User’ Guide 76 Routing Protocol Gateway LAN Interface • Gateway Public IP Address for LAN Interface subnet and NAT

User’ Guide 77 • Authentication mode • Authentication Key Chain Key Chain 1 • Listing of key • Input key Ind

User’ Guide 78 • Click “Submit” to change displayed parameters Reset • Click “Reset” to use displayed parameters,

User’ Guide 79 DHCP Gateway LAN Setup • IP Address (Gateway for private IP subnet in NAT mode) (Gateway for Publ

User’ Guide 8 3. You will see the following Welcome screen. 4. Click “Next>”. You will see the following Start

User’ Guide 80 • Domain Name Service Supports up to four DNSs by clicking “Add” or “Delete” to insert or remove DN

User’ Guide 81 9. DOCSIS configuration file VSIF tag support This feature allows downloading Cable Router configur

User’ Guide 9 5. Click “Next>”. You will see the following ‘Complete’ screen. 6. Click “Finish”. You will see b